THE FUNDAMENTALS OF PLUMBING KNOWLEDGE FOR BATHTUB INSTALLATION

The Fundamentals of Plumbing Knowledge for Bathtub Installation

The Fundamentals of Plumbing Knowledge for Bathtub Installation

Blog Article

Call Today

What are your opinions about Tools You Need to Install a New Bathtub ?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Mounting a bathtub isn't precisely rocket science, yet it does call for solid plumbing, woodworking, as well as often, tiling skills. Changing an old bath tub with a brand-new one is additionally a moderately challenging project. If the old tub is conveniently obtainable, the job can relocate easily; if you have to open up a wall to get rid of the old tub and also position the brand-new tub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will need a helper to vacate the old tub and also embeded in the new one. Make sure you have certified on your own for the job and are comfortable trying it. As opposed to hiring a professional to take control of a halfway-completed task, it is better to take into consideration employing one prior to you begin. Chances are you may need an expert plumber to make tube links.
This article will assist you install a brand-new bath tub in your restroom if you have already purchased a brand-new bathtub as well as don't need to change the arrangement of your previous water pipelines.
Your devices and product list ought to consist of the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Getting ready for the Installation


    First of all, the sustaining frame supplied with the bath must be fitted (if called for) according to the manufacturer's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is very important to see to it that if the tap features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps device to avoid stress on the bathtub.
    Fit the adaptable tap ports to the bottom of the two faucets utilizing 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the provided washers.
    Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must currently be ready to be suited its final setting.

    Removing Old Touches


    If you need to change old taps with new ones as a part of your setup, then the first thing you ought to do is detach the supply of water. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome due to the limited accessibility that is usually the situation.
    Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the staying water that will come from the pipelines. Once the supply pipes have been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. When the taps have actually been removed, the holes in the bath/basin will have to be cleansed of any old sealing substance.
    Prior to proceeding to fit the brand-new faucets, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.

    Installing the Tub


    Making use of both wood boards under its feet, place the bathtub in the needed setting. The wooden boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four tiny factors.
    The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub up until the level reads degree.
    To mount taps, fit all-time low of the furthest flexible faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
    Turn on the supply of water and inspect all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the bathtub and likewise check the overflow outlet as well as the normal electrical outlet for leakages.
    Lastly, take care of the bathroom paneling as explained in the maker's instruction manual. Tiling and sealing around the bath tub needs to wait up until the tub has been used at the very least once as this will resolve it right into its final placement.

    Fitting New Touches


    If the tails of the new faucets are plastic, after that you will require a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the existent supply pipelines.
    If you need to fit a monobloc, then you will certainly call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
    Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in place between the tap and also the sink. Safeguard the tap in place with the manufacturer offered backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet connectors. The former kind ought to be linked to the faucet ends first, tightening up just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Tiling Around the Bathtub


    In the area where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, triggering the water to pass through the wall in between the bathroom and the tiling, bring about difficulties with wetness and possible leakages to the ceiling listed below.
    You can select from a variety of coloured sealants to blend in your components as well as installations. They are marketed in tubes and also cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to permit the movement experienced when the tub remains in usage. The sealant can split rather early if you do not think about this activity before sealing.
    Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly offered on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    I was made aware of that write-up on Installing A Bathtub through someone on our other website. For those who liked our blog entry please remember to pass it around. Thank you so much for going through it.


    Instant fix? Dial!

    Report this page